Menu
RAPIX Software
RAPIX Addressing
RAPIX Addressing is the simple, fast and mobile solution for DALI Short Addressing.
To use RAPIX Addressing you will need a uDID – USB to DALI Interface Device:
Release Notes
Version 10.11.0, added: 17 November 2022
Improvements
- Installer changes to better handle uninstallation of older versions of RAPIX Addressing.
RAPIX Addressing v10.10 (26 October 2022)
- Fixed the error that was appearing when programming Dry Contact on RAPIX Motion Sensor.
- Increased time-out on mobile phone before showing error message.
- Fixed display of selected colour in colour control templates.
- Fixed the issue with Confirm All Devices sometimes not working and Confirm individual device sometimes showing unnecessary warning.
- New colour control templates.
- Fixed exception that could occur when opening DALI Log.
- Fixed the issue with USI live device GUI not opening if there are programmed disable rules.
- Fixed problem with setting the eHub rotary resolution.
- Updated Motion Sensor with Exit Delay template.
- Show an error message if function test or duration test fails to start on the device configuration dialogue.
- When using Go Mobile, show error if phone goes out of WiFi range.
- Prevent double click on mobile web page on iPhone from zooming.
- Added support for new products:
- RAPIX Push Buttons
- RAPIX Diva Buttons
- RAPIX Dials
- Added Tools menu item to allow stopping EM Function and Duration tests on site.
- Allowed copying and pasting of DALI device properties.
- Show pop-up hint on addressing tab showing compound device details.
- Added Zone Tracking template.
- Added Zone Logic template.
- Improved logged DALI message when there is no Forward Frame.
- In DALI Log, show details when setting colour or fade time.
- Fixed problem in Mobile phone control where you could not navigate away from an unpowered DALI Line.
- Fixed eHub motion sensor channel appearing without motion sensor inputs.
- Warn if user has set warmest CT above coolest CT.
- Allow wider selection of colour temperatures from addressing tab.
- Warn user if pasting blank device configuration to another device.
- Fixed exception when swapping eHub channels.
- Show missing custom template ID on the error dialogue when loading programming from a RAPIX device.
- When confirming a compound device where there is a minor mismatch in type, retain as much configuration data as possible.
- Improved options for correcting mis-matched eHub channel.
- Prevented exception occurring in some rare cases when scanning DALI line in RAPIX Addressing.
- Allow scrolling on mobile phone button and sensor identify pages.
- Fixed display of compound device type.
- eHub GUI will now offer to Configure New channel whenever there is a channel type mismatch between DB and live.
- Rotary and sensor inputs on eHub GUI will appear as circles while push button inputs will appear as rectangles with rounded corners.
- New features for mobile phone use:
- Allow user to select DALI Line.
- Identification of RAPIX buttons.
- Identification of RAPIX sensors.
- New options for allocating short addresses
- Don’t use Short Address 0.
- Allocate SA starting from low SA, or starting from high SA.
- Improvements
- Improved reporting of compound device types.
- Fixed problem with reporting results of Short Address allocation.
- Fixed problem with sync check of compound devices.
- Allowed selecting Dynamic Fast Fade Time for LED DALI devices.
- Support for DALI Devices that implement multiple device types (“Compound Devices”).
- Copy and paste of all templates from one RAPIX Device to another (sensors and Universal Input) without having to open the editor.
- New icon for showing device sync status.
- Allow sync of just selected devices.
- Added Bistable Dry Contact Toggle (Advanced) template.
- Fixed Dimmer Timer template.
- Fixed operation of mobile phone control of group 15.
- Renamed various items for clarity.
- Fixed USB DID Driver installer sometimes not installing the driver on new Win10 and Win11 laptops.
- Improved info links that navigate to Ozuno web site.
- Added new template Scene Sequence (bistable dry contact).
- Updated USB DID Driver.
- Added new “Dial with Selectable Granularity” template.
- Improved the Xi Flag Change Event template.
- Improved the Xi Operating Property Change Event template.
- Hide “dial” templates for dry contact inputs.
- In template editor, added text next to expand/contract chevron to show its purpose.
- Fixed problem with colour select form not allowing colour selection for some devices.
- Added a DALI Query log filter option to enable the background query messages to be hidden.
- Fixed problem with setting DALI scene colour.
- The DALI log window will be removed from the task bar when closed.
- Updated the Technical Support tab on the About box.
- Added location information for every DALI device.
- Updates for log form:
- Added option for viewing Button Pressed events to the Log Form.
- Added Walk Test mode to Log Form.
- DALI-2 support:
- handle 8 byte serial numbers
- show PING command in log
- Improved handling of DALI Devices that don’t reply to valid READ MEMORY LOCATION commands.
- Fixed problem with bottom of log filter view hidden.
- Allow setting the group membership of multiple devices on the Group tab using SHIFT + Click.
- New Templates
- Toggle Dimmer with Exit Delay
- Motion Sensor with Two Delays
- In Short Address list, highlight missing
- Closing the DALI log now leaves it paused in the background so that the logged data is not lost.
- In template drop-down lists, show items in sorted order.
- Improved the wording of some error messages.
- Improved the description of some templates.
- When resolving address conflicts, attempt to move devices back to their correct address.
- Added Help menu.
- New templates:
- Light Level Report.
- Do Nothing.
- When hovering mouse over DALI Line shown in red, show hint describing problem.
- Fixed problem with slave sensor template.
- When using mobile phone to move, confirm or unconfirm devices, show device confirmed status (i.e. black).
- Prevent exception when re-addressing devices.
- Prevent exception when converting from Colour Temperature to RGB.
- Added pop-up hint for everywhere that the perceived brightness “eye” icon is used.
- Improved error message when saving to eHub fails.
- While updating eHub or Xi Device firmware, prevent the rest of the program from being used.
- Changed the default scene fade time to 1 second.
- Improvements to eHub and Xi Disable Rule forms:
- Allow long names to be seen in drop-down lists.
- Sort items in drop-down list.
- Increased width of columns.
- Show a hint for long descriptions.
- Clarified error message when trying to use an unused scene in a disable rule.
- New scene sequence template.
- The “Disable Out-of-box Behaviour” feature for Xi Sensors and Universal Inputs.
- Clearing all addresses now includes Xi Devices.
- Fixed exceptions.
- Added support for the Long Range Xi Sensor.
- Disabled indicator for Scene Cycle/Sequence templates.
- Split room join template into three for clarity. Removed unused timer from toggle dimmer template.
- Fixed bug with setting colour scenes.
- Templates
- Added more blind control templates.
- RAPIX Mobile
- Allow addressing Xi Devices.
- Allow setting DALI groups.
- Allow DALI line scan.
- Show basic info about the DALI Line.
- Fixed ConstraintException Value ‘-1’ occurring sometimes when adding new Xi Scene.
- Templates
- Fixed Scene Cycle template.
- Improved handling of templates for dials.
- Added Scene Cycle 2 button template for colour control.
- Updated Scene Cycle template to work with button click as an option.
- Added new option to Scene Timer template.
- On Scene Blast form, added all/none buttons for mask.
- Fixed sorting of schedule events by time.
- Improved reliability of the eHub firmware update over Ethernet.
- Don’t show warning about no NTP on the eHub 3.0 GUI if there is no live device.
- Template light level control – allow larger hysteresis and show actual range.
- Fixed problem with TimeZone selection for non-English versions of Windows.
- Increased the height of the header of some templates.
- Fixed DALI group membership change on the Groups view affecting device identification.
- Fixed the ObjectDisposedException exception that could occur when saving Universal Input programming while shortening and opening its dry contacts.
- Fixed exception that could occur on eHub GUI when updating Ethernet info on the Info view.
- Changed the way that eHub scenes are stored to fix issue with scene indicators.
- Added Blind-control templates.
- Added sunset switch for scenes template.
- Added mode selection to Motion Sensor with Exit Delay template.
- Log DALI Type 4 Application Extended Commands.
- Added support for DALI-2 devices.
- Fixed the eHub 3.0 Schedules disabling feature.
- Improved when warning message about no NTP service appears on the eHub 3.0 Schedules view.
- Fixed Go Mobile help page scrolling and phone simulator.
- Improved support for RGBWAF DALI Type 8 devices.
- Improved logging of exceptions related to opening Device Catalogue.
- Fixed the eHub programming not loading from live device if it was programmed with a Scene Cycle template.
- Fixed the exception sometimes occurring when clicking Clear button on the Xi Sensor GUI.
- IP address on the eHub 3.0 Info tab is now a clickable URL.
- Don’t show Schedule info on the Xi Sensor and Universal Input GUIs.
- Improved Xi Change templates.
- Stopped showing warning about no NTP on the eHub 3.0 GUI Schedules tab when device is configured to Accept NTP Broadcasts.
- Added support for eHub Schedules.
- Added information on eHub editor to show details of Ethernet and NTP (for eHub firmware 3.0 or later).
- Added buttons to unconfirm all devices and clear short address of all devices.
- Raise an error when attempting to edit Xi device entry when its DB and live types do not match.
- Added help buttons to various locations to show related App Note.
- Prevented internal event templates from appearing in the list of available templates when programming Xi Sensor.
- Prevented PC from going to sleep when updating eHub or Xi Device firmware.
- Stopped showing the error message about device type conflict when moving device to a different address.
- Replaced Common Area Control template with two new ones.
- Fixed header height on templates. Fixed maximum pulse level in templates.
- In scene templates, added hyperlink to colour control App Note.
- Allowed adding eHub v3.0 and eHub v2.3 to database.
- Fixed the eHub firmware import throwing exception when importing from a network drive starting with double slash.
- Fixed an exception occurring sometimes when confirming short addresses or using RAPIX Mobile.
- Removed the Add button from the eHub GUI Templates page.
- Clarified some of the eHub error messages.
- Improved firmware update of Rapix Emergency DALI devices.
- Fixed the “Could not open project” error appearing when attempting to open a project.
- Improved description of scene templates.
- Improved behaviour with templates containing multiple DALI Scenes such as Scene Cycle.
- Improved Motion Sensor templates.
- Added Scene Cycle DALI template.
- Added link to help/support information to some templates.
- Allowed selecting colour on the Scene Blast dialogue.
- Added Scene Auto-create to the Scene Blast dialogue.
- Fixed the issue with getting device status from the offline devices.
- Programming of Rapix input devices can now be force-saved, i.e. DB programming can be saved to live device even if nothing was changed on the device configuration dialogue.
- Don’t allow using empty zones in Rapix input devices.
- Added Common Area Control template.
- Added main menu item Tools\View Logs.
- Show the correct number of inputs for the Universal Input device in database.
- Allowed RAPIX Addressing download and automatically install RAPIX Input firmware images.
- Updated Rapix TeamViewer Client to the latest version.
- Excel export of eHub Disable Rules.
- Fixed the DALI logger issue where it would stop logging all traffic on a DALI line after receiving an unknown/malformed forward frame.
- New installer:
- Install software in \Program Files (x86)\Ozuno instead of \Program Files (x86)\Diginet
- Store project files in \Documents\Ozuno instead of \Documents\Diginet
- Store templates and firmware in \ProgramData\Ozuno instead of \ProgramData\Diginet
- Changed registry settings from HKEY_CURRENT_USER\Software\Diginet to HKEY_CURRENT_USER\Software\Ozuno
- Added templates:
- Dim Only
- Set Scene and Flag
- Toggle (Long Press)
- Bell Press (Long Press)
- Dial/Button Dimmer
- Improved template filtering to hide infrequently used templates.
- Fixed device identification not working on the Xi device f/w update dialogue.
- Fixed Dry Contact state sometimes appearing as Closed on UI even when that DC is actually open.
- Added support for XY colour.
- Fixed the Colour Value not saving to the Scene Colour table in the project database.
- Fixed problem with colour devices not having auto activation enabled.
- Added support for the Rapix Xi Universal Switch Input.
- Improved support for colour
- Allowed setting colour for the selected devices, groups and broadcast. Also allowed the Set Colour dialogue height change dynamically when selecting colour type.
- Added colour details to project report.
- Dynamic tooltip and icon on the Addressing view for non-compliant devices, errors, sync and other issues.
- Reworked identification of the eHub channels and added identification of eHub individual inputs.
- Groups and scenes will now be automatically preselected in the identification drop-down list when selecting them on the Groups and Scenes views.
- Added dial/dimmer template.
- Disabled Xi device editing when device’s DB and network types are different.
- Allowed resizing the Device Name column on the Addressing view. The column size will be set to default when software starts.
- Fixed bug with saving MASK colour to live devices from DALI device editor.
- In DALI Device editor, if GTIN or serial is invalid, show as “N/A”.
- Fixed a problem with resetting DALI Type 8 devices.
- Changed the Motion and Light Level Sensor template name to Motion in Darkness.
- Fixed Motion Sensor With Exit Delay template.
- Fixed the issue with Global DALI Device Programming not saving scene changes to live devices.
- It will no longer be possible to accidentally delete confirmed devices when deleting multiple selected devices.
- Allowed unconfirming Xi address if it happened to be occupied by a DALI interface device after address conflict resolution.
- Improved the appearance of title on the Network, Zones and Xi Scenes views when resizing panels with a splitter.
- Prevented the Network Interfaces tree from expanding when main window maximises.
- Confirming Xi device will now change the database device type if it is not the same as on live device.
- Fixed the Xi Sensor motion indicator green ring not appearing on GUI when motion is detected.
- eHub GUI will no longer show a dry contact open or closed state if there is no live device.
- Project Report now includes eHub internal events.
- Fixed an exception occasionally occurring when changing device’s address.
- Fixed the Disable Rules dialog not appearing for an Xi Sensor dry contact.
- Updated the Tech Support tab on the About box.
- Improved Dry Contact usage by allowing dimmer and advanced templates.
- Improved Toggle Advanced template.
- Reduced log time stamp decimal places.
- Fixed the NullRefernceException occurring when starting RAPIX Addressing on Windows 7 that has Firewall blocking Mobile web server port.
- Improved Add Device dialogue
- Improved filtering of allowed templates on a RAPIX DALI Xi Occupancy Sensor dry contact.
- Added Motion Sensor and Exit Delay template.
- Tidied templates that use internal events.
- Added Ozuno web site link to the About box.
- Added Xi Devices Global Programming.
- Improved Dry Contact usage by allowing dimmer and advanced templates.
- Improved Toggle Advanced template.
- Reduced log time stamp decimal places.
- Fixed the NullRefernceException occurring when starting RAPIX Addressing on Windows 7 that has Firewall blocking Mobile web server port.
- Improved Add Device dialogue
- Improved filtering of allowed templates on a RAPIX DALI Xi Occupancy Sensor dry contact.
- Added Motion Sensor and Exit Delay template.
- Tidied templates that use internal events.
- Added Ozuno web site link to the About box.
- Added Xi Devices Global Programming.
- Added support for the RAPIX DALI Xi Occupancy Sensor.
- Added project export to Excel.
- Display the current light level sensor reading on the eHub GUI.
- Added the Motion and Light Level Sensor template.
- Fixed all exceptions reported by users.
- Fixed the Confirm All button remaining disabled after unconfirming a device.
- Software auto-update changed to use a new server.
- Clarified what type of eHub input can be used with each template.
- Improved local interface detection by the Fast Scan.
- Improved German translations.
- Fixed issues with editing multi-selected colour devices.
- Added support for DALI Type 8 (Colour Control) devices.
- Changed DALI device default fade time/rate to “dynamic”.
- Fixed Tool/Export Logs menu item.
- Fixed selection of “live” grid in RAPIX Addressing.
- Enable missing DALI Devices to be seen more easily.
- Added FAST SCAN (i.e. scan for new devices).
- Fixed the check for updates incorrectly detecting an Emergency device firmware, which has already been previously downloaded.
- Fixed logging of forwarded sensor events.
- Updated RAPIX Addressing Manual and added it to the installer.
- Prevented DALI line scan from moving new discovered DALI devices to the confirmed addresses.
- Copying and pasting Scene Control (New Scene) templates on the eHub GUI will paste them as Scene Control templates.
- Fixed the Scene Control (New Scene) template programming occasionally losing Member and scene info.
- Improved the Database/Live filter pre-selection on the Addressing view for USB DALI lines.
- Changed in-line editing of DALI Device name on the Addressing view. Press F2 to edit non – default device name.
- Default the DB/Live Addressing View grids to DB when there is no live network, and default them to live when network is available.
- Open DALI device properties editor on double-click from the Groups and Scenes views.
- Light level sensor calibration dialog now allows setting light level above 1000 Lux.
- Renamed the ‘Save to Network’ check box on the DALI Device editor to ‘Save to Live Device’.
- Improved display when editing multiple DALI Devices.
- Disabled the on/off/level buttons when eHub is selected.
- Log RAPIX software version when software starts and project file name when loaded.
- DALI Logger: Simplified the DALI Logger filter by merging the Command filter with the Message Type filter.
- DALI Logger: The DALI Logger Message Type filter configuration is remembered and applied when the DALI Logger window opens.
- DALI Logger: Imported log file now uses time zone from the site.
- Templates: Show template ID and version at top of template editor.
- Templates: Improved the way that the timer template handles other sources controlling the Zone.
- Templates: Improved the Motion Sensor template pop-up hint.
- Added template: Power Up Action.
- Fixed an exception occurring sometimes when swapping addresses.
- Improved tool-tips in the grid on the Addressing view to include device names and other info.
- Made eHub peripheral product information accessible on eHub main GUI via channel pop-up menu.
- Added Project Save As.This can be used for creation of project backup copies.
- Added eHub Dry Contact state visual indication to eHub GUI.
- Added DALI line conflict resolution summary.
- Show device type as Unknown if it does not reply to the Query Device Type command.
- Improved sorting of DALI devices on the Groups and Scenes views.
- Improved logging of uDID generated messages.
- Improved the format of the date and time messages appearing in the DALI logger.
- Improved the Motion Sensor template.
- Improved templates filtering on the Template Selection dialogue.
- Improved eHub programming when 5 or more slave sensors are used.
- Don’t show the Start Function Test and Start Duration Test buttons on the DALI device GUI when editing multiple devices.
- Improved the Dimmer Timer template.
- Added firmware update for RAPIX Xi devices (under tools menu).
- Added a button for deep scan.
- Added Reboot button to eHub GUI.
- Added the Duration Test Results DALI EM device status information.
- Added the ability to start and stop the Function and Duration emergency tests.
- Explained what the Maintain Zone State option means in the motion sensor templates.
- Explained dwell duration in template description.
- Show scene name in tool-tips on eHub GUI.
- Show eHub port details on eHub GUI Advanced tab.
- Improved behaviour of toggle timer in Timer templates.
- Improved behaviour of motion sensor templates.
- Improved behaviour of Zone and Xi Timer template.
- Default programming for eHub LCD should be to have beep ON.
- Other minor improvements.
- eHub firmware update over DALI (under tools menu).
- Added template “Zone and Xi Timer”.
- Added DALI Level option for adjacent zones to the “Motion Sensor Advanced” template.
- Fixed the DALI Logger short address filter.
- eHub Scripts Update
RAPIX Integrator
RAPIX Integrator – the professional tool for commissioning a RAPIX Lighting System.
To use RAPIX Integrator: the connection to a DALI line is made using a uDID – USB to DALI interface Device.
Alternatively, all DALI lines in an installation can be commissioned through one or more RAPIX Zone Controllers.
Release Notes
Version 10.11.0, added: 17 November 2022
Improvements
- Allow use of email server port number greater than 100.
- Allow selection of secondary Zone Controller for Modbus connection.
RAPIX Integrator v10.10 (26 October 2022)
- Fixed the error that was appearing when programming Dry Contact on RAPIX Motion Sensor.
- Increased time-out on mobile phone before showing error message.
- Fixed display of selected colour in colour control templates.
- Fixed the issue with Confirm All Devices sometimes not working and Confirm individual device sometimes showing unnecessary warning.
- New colour control templates.
- Show Interface ID as an option on the tree view and allow collapsing and expanding interface nodes.
- Fixed exception that could occur when opening DALI Log.
- Fixed the issue with USI live device GUI not opening if there are programmed disable rules.
- Show warning when adding interface device with duplicate IP Address.
- Made DALI Line Name edit boxes wider.
- Fixed problem with setting the eHub rotary resolution.
- Updated Motion Sensor with Exit Delay template.
- Highlight Project Transfer button when any of these change: users, unencrypted connections, zones, scenes, user scripts, schedules, zones used by Rapix Input devices.
- Show an error message if function test or duration test fails to start on the device configuration dialogue.
- When using Go Mobile, show error if phone goes out of WiFi range.
- Prevent double click on mobile web page on iPhone from zooming.
- Fixed resizing and closing of RAPIX API form.
- Added support for new products:
- RAPIX Push Buttons
- RAPIX Diva Buttons
- RAPIX Dials
- Added Tools menu item to allow stopping EM Function and Duration tests on site.
- Allowed copying and pasting of DALI device properties.
- Show pop-up hint on addressing tab showing compound device details.
- Added toolbar buttons to Zones, Scenes and Xi Properties views to allow showing Zone ID, Sense ID, Operating Property Number and Flag Group Value.
- Added Zone Tracking template.
- Added Zone Logic template.
- Improved logged DALI message when there is no Forward Frame.
- In DALI Log, show details when setting colour or fade time.
- Fixed problem in Mobile phone control where you could not navigate away from an unpowered DALI Line.
- Fixed eHub motion sensor channel appearing without motion sensor inputs.
- Warn if user has set warmest CT above coolest CT.
- Fixed exception when showing floor plans.
- Allow wider selection of colour temperatures from addressing tab.
- Fixed problem with scripts continuing to run if not recompiled after deleting last script.
- Warn user if pasting blank device configuration to another device.
- Fixed exception when swapping eHub channels.
- Show missing custom template ID on the error dialogue when loading programming from a RAPIX device.
- Improved sorting by time on the schedules tab.
- When confirming a compound device where there is a minor mismatch in type, retain as much configuration data as possible.
- Improved options for correcting mis-matched eHub channel.
- Prevented exception occurring in some rare cases when scanning DALI line in RAPIX Addressing.
- Order child eDIDs by name when rendering tree of interfaces and DALI lines on the Network view.
- Allow scrolling on mobile phone button and sensor identify pages.
- Fixed display of compound device type.
- eHub GUI will now offer to Configure New channel whenever there is a channel type mismatch between DB and live.
- Rotary and sensor inputs on eHub GUI will appear as circles while push button inputs will appear as rectangles with rounded corners.
- Fixed child eDIDs sometimes appearing in swapped order in the interfaces treelist on the Network view.
- Allow user to select DALI Line.
- Identification of RAPIX buttons.
- Identification of RAPIX sensors.
- Don’t use Short Address 0.
- Allocate SA starting from low SA, or starting from high SA.
- Allow RAPIX Integrator to discover and configure eDIDs that are on different subnets.
- Improved reporting of compound device types.
- Fixed problem with reporting results of Short Address allocation.
- Allow a user to select less than 4 schedule groups in auto-build for RAPIX Facilities.
- Allowed editing offline eDID.
- Fixed problem with sync check of compound devices.
- Allowed selecting Dynamic Fast Fade Time for LED DALI devices.
- New features for mobile phone use:
- Allow user to select DALI Line.
- Identification of RAPIX buttons.
- Identification of RAPIX sensors.
- New options for allocating short addresses
- Don’t use Short Address 0.
- Allocate SA starting from low SA, or starting from high SA.
- Improvements
- Improved reporting of compound device types.
- Fixed problem with reporting results of Short Address allocation.
- Fixed problem with sync check of compound devices.
- Allowed selecting Dynamic Fast Fade Time for LED DALI devices.
- Fixed the issue with not being able to select remote zone on eHub on a child eDID DALI line.
- Added support for the new software RAPIX Facilities.
- Added RAPIX API dialogue.
- Fixed USB DID Driver installer sometimes not installing the driver on new Win10 and Win11 laptops.
- Added scroll to Zone Controller Properties tab.
- Improved info links that navigate to Ozuno web site.
- Added new template Scene Sequence (bistable dry contact).
- Updated USB DID Driver.
- Added support for using an EDID as an additional Zone Controller DALI interface. (Application Note PDF)
- Allow Zone Controller date and time to be set from RAPIX Integrator.
- Added new “Dial with Selectable Granularity” template.
- Auto-fill IP settings when adding a DALI Interface.
- Improved the Xi Flag Change Event template.
- Improved the Xi Operating Property Change Event template.
- Hide “dial” templates for dry contact inputs.
- In template editor, added text next to expand/contract chevron to show its purpose.
- Fixed problem with colour select form not allowing colour selection for some devices.
- Fixed problem with Zone Controller properties tab sometimes incorrectly showing “Network properties are misconfigured”.
- Various minor improvements to the Project Report.
- Fixed the logic “catch-up” process.
- Added confirmation for excluding logic modules to make it harder to do by accident.
- Allow Zone Controller date/time to be set from RAPIX Integrator (useful for testing schedules and logic).
- Added a DALI Query log filter option to enable the background query messages to be hidden.
- Fixed problem with setting DALI scene colour.
- Fixed the “Discover” button for adding new Zone Controllers.
- The DALI log window will be removed from the task bar when closed.
- Updated the Technical Support tab on the About box.
- Show eHub schedules on schedules tab.
- Added list of project-related contacts.
- Added site address property.
- Added location information for every DALI device.
- Updates for log form:
- Added option for viewing Button Pressed events to the Log Form.
- Added Walk Test mode to Log Form.
- DALI-2 support:
- handle 8 byte serial numbers
- show PING command in log
- Added support for new Zone Controller mesh.
- Improved handling of DALI Devices that don’t reply to valid READ MEMORY LOCATION commands.
- Don’t allow selection of USB Zones in Schedules or Logic.
- Fixed problem with listing sensors in project summary.
- In project report, show complete list of Zones and Scenes sorted by name and by id.
- Fixed problem with bottom of log filter view hidden.
- Fixed problem with creating Zone Controller summary from compact log file.
- Allow setting the group membership of multiple devices on the Group tab using SHIFT + Click.
- New Templates
- Toggle Dimmer and Xi Flag
- Toggle Dimmer with Exit Delay
- Motion Sensor with Two Delays
- Help button for getting Zone Controller logs
- In Short Address list, highlight missing devices.
- Closing the DALI log now leaves it paused in the background so that the logged data is not lost.
- Allow better resizing of logic editor.
- In template drop-down lists, show items in sorted order.
- Improved the wording of some error messages.
- Improved the description of some template descriptions.
- Support changes to Zone Controller scan process.
- When resolving address conflicts, attempt to move devices back to their correct address.
- Fixed problem with importing DALI Log from Zone Controller with no project.
- Zone Controller Report (lists details of all connected Zone Controllers).
- Added ability to set Zone Controller log level from RAPIX Integrator.
- Added Help menu.
- New templates:
- Light Level Report.
- Light Level Operating Property.
- Do Nothing.
- Support for new Zone Controller DALI Log:
- In Log Form, added import of DALI Log (conversion to RI log format).
- In Log Form, added button to generate summary data file for graphing of parameters over time.
- Fixed Motion Sensor Slave template not working on Dry Contact inputs of Xi Sensor and Universal Input devices.
- When hovering mouse over DALI Line shown in red, show hint describing problem.
- Fixed problem with slave sensor template.
- Updates to logic manual.
- When using mobile phone to move, confirm or unconfirm devices, show device confirmed status (i.e. black).
- Prevent exception when re-addressing devices.
- Prevent exception when converting from Colour Temperature to RGB.
- If there are 6 DALI Interfaces or less, show the project tree expanded.
- In the Select Remote Zones form, allow local Zones to be selected also.
- Show error message when transferring currently open project from Zone Controller.
- Added pop-up hint for everywhere that the perceived brightness “eye” icon is used.
- Improved error message when saving to eHub fails.
- While updating eHub or Xi Device firmware, prevent the rest of the program from being used.
- Changed the default scene fade time to 1 second.
- Improvements to eHub and Xi Disable Rule forms:
- Allow long names to be seen in drop-down lists.
- Sort items in drop-down list.
- Increased width of columns.
- Show a hint for long descriptions.
- Clarified error message when trying to use an unused scene in a disable rule.
- Logic
- Added support for serial ports.
- Added level conversion methods.
- Added IsFirstRun property.
- Allow an excluded module to be edited.
- Fixed problem with logic messages sometimes not shown in RAPIX Integrator log.
- Changed name of top-level logic tree node from “Standard” to “Modules” to reduce confusion. Updated help file to match.
- New scene sequence template.
- Added ability for log to show Zone Controller Master/Slave arbitration system events.
- The “Disable Out-of-box Behaviour” feature for Xi Sensors and Universal Inputs.
- Logic
- Clearing all addresses now includes Xi Devices.
- Speed-optimised Project Transfer to Zone Controllers.
- Improvements to Project Report:Fixed DALI Scene usage.
- Made DALI Scene tables more compact.
- Warn if DALI Groups and DALI Scenes are defined but not used.
- Warn if firmware version is not the same across ZCs in the project.
- Fixed issue with Project Report where a Zone is used in more than one scene.
- Added list of the Xi Operating Properties and Xi Flags to the Project Export (for use with third-party systems).
- Fixed exceptions.
- Allowed updating OS on multiple zone controllers in parallel.
- Clarified confirmation messages for zone controller f/w update, OS update, Reboot and Clear actions.
- Added support for the Long Range Xi Sensor.
- Disabled indicator for Scene Cycle/Sequence templates.
- Split room join template into three for clarity. Removed unused timer from toggle dimmer template.
- Fixed bug with setting colour scenes.
- Updated the format of the export project data file.
- Project Report
- Test for overlapping Zones in Project Report.
- Templates
- Added more blind control templates.
- RAPIX Mobile
- Allow addressing Xi Devices.
- Allow setting DALI groups.
- Allow DALI line scan.
- Show basic info about the DALI Line.
- Fixed ConstraintException Value ‘-1’ occurring sometimes when adding new Xi Scene.
- Project Report
- In the project summary, highlight items that are a potential problem.
- Show Zone tracking rules in project summary.
- Fixed error with project report not showing Xi Input Dry Contact info.
- Added details of redundant Zone sync rules to Project Report.
- Templates
- Fixed Scene Cycle template.
- Improved handling of templates for dials.
- Added Scene Cycle 2 button template for colour control.
- Updated Scene Cycle template to work with button click as an option.
- Added new option to Scene Timer template.
- On Scene Blast form, added all/none buttons for mask.
- Fixed sorting of schedule events by time.
- Added Catch-Up options for Zone Controller schedules.
- Allow selection of Zone Controller status scan period.
- In project report, show break-down of device types.
- In project report, warn if a Zone has lots of short addresses.
- Improved reliability of the eHub firmware update over Ethernet.
- Don’t show warning about no NTP on the eHub 3.0 GUI if there is no live device.
- Template light level control – allow larger hysteresis and show actual range.
- Fixed problem with TimeZone selection for non-English versions of Windows.
- Increased the height of the header of some templates.
- Fixed DALI group membership change on the Groups view affecting device identification.
- Fixed the ObjectDisposedException exception that could occur when saving USI programming while shortening and opening its dry contacts.
- Improved reliability of sorting of schedules in the Schedules tree-view after adding, removing or editing a schedule.
- Fixed exception that could occur on eHub GUI when updating Ethernet info on the Info view.
- Changed the way that eHub scenes are stored to fix issue with scene indicators.
- Fixed the issue with Scene view showing incorrect parent eHub.
- Added Blind-control templates.
- Added sunset switch for scenes template.
- Added mode selection to Motion Sensor with Exit Delay template.
- Log DALI Type 4 Application Extended Commands.
- In project report, show DALI version.
- Added support for DALI-2 devices.
- Fixed the eHub 3.0 Schedules disabling feature.
- Improved when warning message about no NTP service appears on the eHub 3.0 Schedules view.
- Fixed Go Mobile help page scrolling and phone simulator.
- Improved support for RGBWAF DALI Type 8 devices.
- Improved logging of exceptions related to opening Device Catalogue.
- Fixed the eHub programming not loading from live device if it was programmed with a Scene Cycle template.
- Fixed the exception sometimes occurring when clicking Clear button on the Xi Sensor GUI.
- IP address on the eHub 3.0 Info tab is now a clickable URL.
- Don’t show Schedule info on the Xi Sensor and Universal Input GUIs.
- Improved Xi Change templates.
- Stopped showing warning about no NTP on the eHub 3.0 GUI Schedules tab when device is configured to Accept NTP Broadcasts.
- Schedule name edit box will now appear on the Schedules view.
- Added support for eHub Schedules.
- Added information on eHub editor to show details of Ethernet and NTP (for eHub firmware 3.0 or later).
- Added buttons to unconfirm all devices and clear short address of all devices.
- Added error messages when adding scenes and schedules to project with no Zone Controllers.
- Show when scenes are stored in Xi Device.
- Raise an error when attempting to edit Xi device entry when its DB and live types do not match.
- Added clear project button to Zone Controller view.
- Added help buttons to various locations to show related App Note.
- Prevented internal event templates from appearing in the list of available templates when programming Xi Sensor.
- Prevented PC from going to sleep when updating eHub or Xi Device firmware.
- Stopped showing the error message about device type conflict when moving device to a different address.
- Improved performance of loading live eHub programming on large projects.
- Replaced Common Area Control template with two new ones.
- Fixed header height on templates. Fixed maximum pulse level in templates.
- In scene templates, added hyperlink to colour control App Note.
- Allowed adding eHub v3.0 and eHub v2.3 to database.
- Fixed the eHub firmware import throwing exception when importing from a network drive starting with double slash.
- Fixed an exception occurring sometimes when importing Zone Controller firmware file from email attachment.
- Fixed an exception occurring sometimes when confirming short addresses or using RAPIX Mobile.
- Removed the Add button from the eHub GUI Templates page.
- Clarified some of the eHub error messages.
- Improved Xi Flag Group presentation in the Project Report.
- Improved firmware update of Rapix Emergency DALI devices.
- Fixed the “Could not open project” error appearing when attempting to open a project.
- Made the header of the “Set Static IP Address” dialog taller so that all text on it could be clearly visible.
- Improved description of scene templates.
- In the Scene Member list, show correct info for colour when there is a DALI Scene selected. Same for project report.
- Button to show help for Modbus on the Site view.
- Improved behaviour with templates containing multiple DALI Scenes such as Scene Cycle.
- Improved Motion Sensor templates.
- Added Scene Cycle DALI template.
- Added link to help/support information to some templates.
- Show Scene conflict decoration on the Scenes view when there is a scene colour.
- Allowed selecting colour on the Scene Blast dialogue.
- Added Scene Auto-create to the Scene Blast dialogue.
- Fixed the issue with getting device status from the offline devices.
- Added Modbus config errors to Project Report.
- Improved Project Report.
- Programming of Rapix input devices can now be force-saved, i.e. DB programming can be saved to live device even if nothing was changed on the device configuration dialogue.
- Don’t allow using empty zones in Rapix input devices.
- Improved Zone and Scene member pop-up tooltip.
- Added Common Area Control template.
- Added main menu item Tools\View Logs.
- Modbus error reporting.
- Show the correct number of inputs for the Universal Input device in database.
- Allowed RAPIX Integrator download and automatically install RAPIX Input firmware images.
- Updated Rapix TeamViewer Client to the latest version.
- Excel import/export of eHub Disable Rules.
- Fixed the DALI logger issue where it would stop logging all traffic on a DALI line after receiving an unknown/malformed forward frame.
- Changed Xi Scene label on the Configure Schedule Event dialogue.
- New installer:
- Install software in \Program Files (x86)\Ozuno instead of \Program Files (x86)\Diginet
- Store project files in \Documents\Ozuno instead of \Documents\Diginet
- Store templates and firmware in \ProgramData\Ozuno instead of \ProgramData\Diginet
- Changed registry settings from HKEY_CURRENT_USER\Software\Diginet to HKEY_CURRENT_USER\Software\Ozuno
- Added templates:
- Dim Only
- Set Scene and Flag
- Toggle (Long Press)
- Bell Press (Long Press)
- Dial/Button Dimmer
- Improved template filtering to hide infrequently used templates.
- Added Modbus support.
- Fixed device identification not working on the Xi device f/w update dialogue.
- Fixed Dry Contact state sometimes appearing as Closed on UI even when that DC is actually open.
- Added support for XY colour.
- Fixed the Colour Value not saving to the Scene Colour table in the project database.
- Fixed problem with colour devices not having auto activation enabled.
- Fixed sunrise/sunset calculations for GMT +12 (e.g. Wellington, New Zealand).
- Added support for the Rapix Xi Universal Switch Input.
- Show which Zone Controller is the Master.
- Supported long fade times (from 2 minutes to 24 hours).
- Improved support for colour
- Allowed setting colour for the selected devices, groups and broadcast. Also allowed the Set Colour dialogue height change dynamically when selecting colour type.
- Allowed setting zone colour from the Zones view.
- Allowed setting colour in Xi Scene.
- Allowed setting colour in Schedule Event.
- Added colour details to project report.
- Added colour details to Excel import/export.
- Dynamic tooltip and icon on the Addressing view for non-compliant devices, errors, sync and other issues.
- Reworked identification of the eHub channels and added identification of eHub individual inputs.
- Groups and scenes will now be automatically preselected in the identification drop-down list when selecting them on the Groups and Scenes views.
- Added dial/dimmer template.
- Disabled Xi device editing when device’s DB and network types are different.
- Allowed resizing the Device Name column on the Addressing view. The column size will be set to default when software starts.
- Improved the subnet mask validation when adding Zone Controller or editing its network settings.
- Improved performance of confirmation of an Xi Device when there is DB and live device type mismatch.
- Fixed bug with saving MASK colour to live devices from DALI device editor.
- In DALI Device editor, if GTIN or serial is invalid, show as “N/A”.
- Fixed a problem with resetting DALI Type 8 devices.
- Changed the Motion and Light Level Sensor template name to Motion in Darkness.
- Fixed Motion Sensor With Exit Delay template.
- Fixed the issue with Global DALI Device Programming not saving scene changes to live devices.
- It will no longer be possible to accidentally delete confirmed devices when deleting multiple selected devices.
- Allowed unconfirming Xi address if it happened to be occupied by a DALI interface device after address conflict resolution.
- Improved the appearance of title on the Network, Zones and Xi Scenes views when resizing panels with a splitter.
- Prevented the Network Interfaces tree from expanding when main window maximises.
- Confirming Xi device will now change the database device type if it is not the same as on live device.
- Fixed the Xi Sensor motion indicator green ring not appearing on GUI when motion is detected.
- Fixed the Duration editor not working properly for the Sunset Switch template when attempting to set values below 30 minutes.
- eHub GUI will no longer show a dry contact open or closed state if there is no live device.
- Improved performance of the DALI Device Global Programming on large projects.
- Project Report now includes eHub internal events.
- Fixed an exception occasionally occurring when changing device’s address.
- Updated Zone Controller link icons and improved their usage.
- Fixed a few issues with Excel import.
- Fixed the Disable Rules dialog not appearing for an Xi Sensor dry contact.
- Updated the Tech Support tab on the About box.
- Use tooltip on the Schedule event dialogue when showing colour values that have long description.
- Allowed user to save just the changes for the eHub and DALI Xi Occupancy Sensor to reduce save time.
- Added editor for eHub internal event templates and removed the need for them to be associated with an unused input.
- Fixed the issue where DALI logger stops working after unrecognised or malformed command.
- Fixed the issue with the Light Level Maintenance template not retaining the selected Light Level value.
- Fixed the NullReferenceException occasionally occurring when closing RI after using DALI logger.
- Allowed resizing the Network view. Splitter distance will be saved when closing software.
- Fixed the mouse wheel scroll down event not working on the Light Level track bar.
- Fixed an issue with the Excel import not using Zone Names in templates. Added additional checks of Zone Controller worksheet data.
- Added Watchdog Timer template.
- Added Motion Sensor and Exit Delay template.
- Excel import/export improvements
- Added Xi Flags and Operating Properties.
- Added Schedules.
- Added Xi Scenes.
- USB DALI lines.
- Fixed the issue where if user puts the “Xi Devices” list twice in a work-sheet, the import gets stuck in an infinite loop.
- Allowed use of Zone and Xi Scene names in import of templates.
- Added Ozuno web site link to the About box.
- Added Xi Devices Global Programming.
- Excel import/export improvements
- Improved handling of Xi Device and Zone Controller extended address conflict.
- Improved Dry Contact usage by allowing dimmer and advanced templates.
- Improved Toggle Advanced template.
- Reduced log time stamp decimal places.
- Clarified on the UI how schedules use Xi Flags and Operating Properties.
- Fixed the NullRefernceException occurring when starting RAPIX Addressing on Windows 7 that has Firewall blocking Mobile web server port.
- Fixed an exception occurring on software start up if user didn’t have write permissions to the Debug.log file.
- Fixed the Project summary not listing Flags used in DALI Xi Occupancy Sensor and Universal Input Dry Contacts.
- Improved Add Device dialogue
- Fixed the Change Template not changing template on a dry contact.
- Added floor plan snap to grid option.
- Save selected floor plan Background Theme to the project database.
- Improved filtering of allowed templates on a RAPIX DALI Xi Occupancy Sensor dry contact.
- Tidied templates that use internal events.
- Improved software performance on large projects when moving, copying or changing eHub input programming.
- Added support for the DALI Xi Occupancy Sensor.
- Added project export to Excel and import from Excel.
- Display the current light level sensor reading on the eHub GUI.
- Added the Motion and Light Level Sensor template.
- Added the Xi Operating Property Action template.
- Fixed all exceptions reported by users.
- Prevented Project Key from having characters that are easily confused on the Zone Controller LCD.
- Fixed the Set and Clear of the Xi Flag not working on USB DALI lines.
- Fixed the Confirm All button remaining disabled after unconfirming a device.
- Software auto-update changed to use a new server.
- Clarified what type of eHub input can be used with each template.
- Improved local interface detection by the Fast Scan.
- Project Report: Sort Zone members.
- Project Report: Do not raise the warning about a zone not being used if it is a sub-zone.
- Fixed issues with editing multi-selected colour devices.
RAPIX Emergency
RAPIX Emergency is the intelligent DALI Emergency Lighting Monitoring System with ‘One Click’ commissioning.
RAPIX Emergency comes in 2 editions:
- World Edition – 3 hours running time, 12 monthly maximum check interval.
- Australian Edition – To suit the Australian country requirements: 90/120 minutes running time, 6 monthly maximum check interval.
A common download is used for both editions, the country requirements are selected during installation. Both editions are FREE software.
Release Notes
Version 6.0.0, added: 30 March 2022
- Allowed importing RAPIX Integrator projects that contain EDIDs.
RAPIX Emergency (DALI) v5.10 (7 February 2022)
- Improved support for DALI “Multiple” device type.
RAPIX Emergency (DALI) v5.9 (10 March 2021)
- Made RAPIX Emergency connect faster to Ethernet DALI interfaces.
RAPIX Emergency (DALI) v5.8 (23 March 2020)
- Combined World Edition and Australian Edition of RAPIX Emergency software into single installer.
- Updated the installer software.
RAPIX Emergency (DALI) v5.7 (08 November 2018)
- The UI performance on large projects has been significantly improved.
- DALI lines in the test reports will be sorted by interface name and then DALI line name.
- 0 minutes test duration instead of blank space will appear on devices that reported 0 minutes duration.
- The test report header section has been expanded to show error percentages grouped by error types.
- Fixed the Out Of Memory exceptions occurring when attempting to reconnect to 80+ Zone Controllers.
RAPIX Emergency (DALI) v5.5 (25 July 2018)
- Simplified software installation and licensing.
RAPIX Emergency (DALI) v5.4 (09 January 2018)
- Test reports in CSV format can now be generated and attached to emails in addition to the standard PDF reports.
- Previous Test Results can now be visible in the Configuration view.
- RAPIX Emergency will now wait for up to 8 hours (instead of 5 hours) when collecting test results after a discharge test before giving up on a device and marking it with “pending test failure”.
- RAPIX Emergency auto-start on Windows startup can now be configured by a Supervisor user.
- The device status pie-chart can now be hidden by a Supervisor user.
- Manual Function Test on All Lines and manual Discharge Test can now be started from the Dashboard.
RAPIX Desktop App
The RAPIX Desktop App allows lighting control from a desktop PC
The RAPIX Desktop App runs on a Windows PC, and allows control of lighting from a system tray icon.
- Easy configuration utility.
- Multiple control widgets can be selected and configured.
- Keeps out of the way until needed.
- Suitable for corporate deployments, can be deployed using Group Policy.
Release Notes
Version 2.0.0, added: 11 October 2022
Rapix Desktop App and Rapix Desktop Configuration Utility
- Allow user to edit schedules.
- Allow user to edit scenes.
- Made the icon always visible.
- Allow cancellation of widget edit
- Updated help file
- Added button to allow password to be viewed. Improved form re-draw.
- Import existing configuration file
- Allow user to edit widgets. Added scroll to widget preview.
- Allow user to delete and rearrange controls.
- Improved theme appearance.
RAPIX Desktop App v1.4 (8 June 2021)
RAPIX Desktop Config v1.4 (8 June 2021)
- Rapix Desktop App
- Added an option for the Zone level widget slider to show Target Level or Actual Level.
- Rapix Desktop Configuration Utility
- Added an option for the Zone level widget slider to show Target Level or Actual Level.
RAPIX Desktop App v1.3 (19 April 2021)
RAPIX Desktop Config v1.3 (19 April 2021)
- Rapix Desktop App
- Fixed problem with RGBW slider values “bouncing back” after a change with some DALI drivers.
- Added logging.
- Rapix Desktop Configuration Utility
- Fixed problem with RGBW slider values “bouncing back” after a change with some DALI drivers.
RAPIX Desktop App v1.2 (1 April 2021)
RAPIX Desktop Config v1.2 (1 April 2021)
- Rapix Desktop App
- Fixed problem with colour temperature slider with high values.
- Fixed problems with slider values “bouncing back” after a change.
- Rapix Desktop Configuration Utility
- Fixed problem with colour temperature slider with high values.
- Fixed problems with slider values “bouncing back” after a change.
- Show real-time data in preview panel.
RAPIX Desktop App v1.1 (25 March 2021)
RAPIX Desktop Config v1.1 (25 March 2021)
- Initial public release
Head Office
Phone: +61 8 8362 7584
Hours: Monday to Friday – 9am to 5pm (Australian Central Standard Time)
Policies
Subscribe
Sign up to keep up to date on our latest product and software developments.